5017S Mounting Model 15 printer motor, typing and keyboard units to the base unit 5187S Using the portable reperforator tables (RT-33 or RT-34) in connection with the metal table (XRT-107) of the Model 19 type set 5220S Instructions for installing, adjusting, and catalog information of the function arms used on the function arm control assembly of the Teletype Model 26 type wheel page printer 5226S Description of Teletype Model 17 radio printer system using 7-line character pattern 5227S (replaced by 5230S) 5229S Instructions for installing and adjusting the 98070 upper case "H" motor control set of parts on Model 26 printer operating on .060 ampere line current 5230S Instructions for installing the 97451, 98137, 101481, 101389, 106922 or 113751 set of parts to provide end of tape stop mechanism and to handle fully perforated, chadless or spliced chadless tape on a Model 14 transmitter distributor (5 unit) also the 113776 set of parts to provide end of tape stop mechanism on a Model 20 transmitter distributor (6 unit) 5237S Description, adjustments, and parts catalog of the Teletype REC-10 rectifier 5269S Description, adjustments, and ordering information - Teletype REC-13 rectifier 5270S Instructions for installing the 99971 resistor assembly on all-metal 15 and 26 type printer tables and all-metal perforator and transmitter distributor tables 5273S Instructions for installing the 103514 resistor unit on XRT-96 or XRT-107 tables for operationg of the 19 type set on 110 volt 25 cycle current 5288S Lubrication supplies and directions for use 5298S Instructions for adjusting, lubricating and preparing Model 17 radio printers for operation 5299S Description, adjustments and parts catalog of the Teletype REC14 rectifier. 5316S Description, adjustments and ordering information Teletype model REC-20 rectifier 5345S U.S. Army Signal Corps Printers TG-7-A, TG-7-B and TG-37-B With Chests CH-50-A and CH-50-B and Chests CH-62-A and CH-62-B 5346S Insturctions for modification of wiring of Printer TG-7-A (Teletype Model 15) for operation with a line relay and a motor control relay 5351S Instructions for Installing the 101177 Set of Control Relay Parts on the 36 Type Printer 5380S General description, Teletype Model 19 page printer set 5381S General description, Teletype Model 15 page printer set 5404S Instructions for installing and wiring the 105402 set of parts on Signal Corps TG-7-B and TG-37-B printers 5469S Instructions for installing and adjusting the 110352 set of parts of adding the ribbon reverse arm yield spring and backstop feature on Model 15 and 20 printers 5472S Instructions for installing the 110478 set of parts for securing an REC13 or REC30 rectifier to Model 19 (XRT114) table 5475S Description of and instructions for assembling Teletype Model 19 page printer set adapted for shipboard use 5482S Instructions for modifying a Model 15 printer from 60 W.P.M. operation to either 75 W.P.M. (using the 96535 or 96536 modification kit) or 100 W.P.M. (using the 110891 or 110892 modification kit) operation 5486S (replaced by 5230S) 5387S Description, adjusting and ordering information Teletype model REC-30 rectifier 5712S Instructions for installing the 115823, 115824, 115842 and 113048 sets of parts to equip Model 15 and Model 20 printers respectively with the new style type bar backstop 5719S Instructions for installing the 152919 set of parts to modify a Model 28 page printer set (typing unit serial nos. 1500 and up) for use in weather map service 5726S Instructions for converting the key lever arrangement on a Model 28 keyboard from "ARA" to "ARC" and from "ARC" to "ARD," "ARB" or "ARA" using the 151934, 152904, 152905 or 152906 respectively 5741S Instructions for installing, adjusting and parts ordering information for the 128700 torn feed hole tape stop assembly, for use on a Model 14 transmitter-distributor 5758S (replaced by 5230S) 5760S Instructions for installing the 152307 modification kit on the Model 28 typing unit LP3, LP4, LP5, LP6, LP7, LP8, and LP9, to provide reperforator control mechanism (H-on, F-off or F-on, H-off) 5765S Instructions for installing the 152915 or 157511 and 152916 or 154145 modification kit on Model 28 typing unit LP4 or LP10 and up and a Model 28 keyboard LK4 or LK6, LAK respectively to provide the local reverse line feed mechanism 5766S Instructions for installing the 152917 or 157510 and 152918, 15416 or 199999 modification kid on a Model 28 or 35 typing unit and keyboard to provide local backspace mechanism 5792S Instructions for installing modification kits (172625, 176181 through 176197, 178568 through 178584, 306686 through 306072, 153926) to convert a Model 28 or 35 friction feed printer set to a sprocket feed printer set and for replacing the 153771 through 153787 guide bracket using teh 159356 modification kit 5804S Instructions for installing the 154785 or 163146 modification kit on a Model 28 typing unit or sequence selector unit to add a universal contact 5809S Instructions for installing the 195837** modification kit to equip the Model 28 cabinets, LAC202 or above and the LAAC200 series with paper supply and accumulating shelf, and the 179393** modification kit to add adjustable form guide to the 192260** and 195837** paper supply and accumulating shelf 5816S Instructions for installing the 153905 or 153914 spacing drum set of parts on a Model 28 typing unit (LP3, LP4, LP5; Bell System 28A) 5821S Instructions for installing the 152902 modification kit for cabinets LAC203**, LAC204**, LAC205** (Bell System 28B, 28C, 28D, 28E) and the 154753 modification kit for typing units LP6, LP9 (Bell System 28E, 28F, 28G) to provide an interim selective calling feature 5827S Instructions for installing the 153920, 154741 or 157532 selective calling modification kit on a Model 28 cabinet LAC203**, LAC204**, LAC205**, LAAC209**, LAAC210** and the 160884 modification kit to provide auxiliary connector for cabinet LAAC206** (for CAA) 5847S Instructions for converting a Model 28 printer set (typing unit LP6, LP9, from Bell system 28B, 28C, 28D to 28E, 28G; and cabinets LAC203**, LAC204**; Bell System 28B, 28C) from non-selective calling to selective calling using teh 153941 or 154758 modification kit 5857S Instructions for installing the 154782 modification kit on a Model 28 typing unit LP6, LP9 and up to prevent associated transmitter distributor from locking out typing unit when nonspacing functions occur 5865S Instructions for installing the Model 28 multi-magnet reperforator set (reperforator LARP1, base LARB1 and motor unit LMU3) 5866S Instructions for installing the 153913 modification kit on a selective calling Model 28 typing unit LP6 or LP9 to provide print suppression during selection for use with single letter C.D.C. operation 5872S Instructions for installing: the 154755, 159395, 163292 or 154792 modification kit on a Model 28 typing unit to provide 5, 6, 8, or 12 spaces respectively, the 154334 modification kit to provide increased ribbon height on units with large gothic type pallets 5880S Instructions for installing and parts ordering information for the 160335 modification kit to add control panel to Model 28 automatic send-receive cabinet LAAC206** 5887S Instructions for installing the 179472 modification kit to provide a transmitter control device for use on FAA equipment 5888S Instructions for installing the 159366 (for Model 28 only) or 194324 modification kit on a Model 28, 29, 34, 35 or 28-32 printer (friction feed) to provide a paper-out alarm switch 5898S Instructions for installing the 161280 modification kit on a Model 28 typing unit to provide on-line operation of the local reverse line feed mechanism 5899S Instructions for installing the 154174 modification kit on a Model 28 keyboard LK6 or LAK to provide repeat space operation 5947S Instructions for installing the 163775 modification kit to equipment Model 28 keybaord LK6 and up or LAK with space-repeat mechanism 5948S Instructions for installing the 162641 or 163359 modification kit on a Model 28 keyboard or base to provide a variable speed drive 5954S Instructions for installing the 164502 modification kit to provide Model 28 send-receive keyboard (LK) and automatic send-receive keyboard base (LAK) with an end-of-message character generator; and instructions for installing the 173122 modification kit to eliminate interference between components of the 164502 modification kit (early design) and 154240 and 162308 code bar reset bails 6889S Engineering specification for the Model 28 transmitter distributor LBXD8 and LBXD22 50001S Instructions for installing the 164272 modification kit to provide chad disposal for the auxiliary reperforator; 170306 modification kit to provide chad disposal for the keyboard reperforator; 166405** and 195391** modification kits to provide chad container for the auxiliary and/or keyboard reperforator. 50015S 174491 Modification Kit to provide radio-frequency filter for signal generator contacts of Model 28 keyboards LK6 and up, LAK, LTPK, LTRK, and transmitter distributor LXD 50039S Instructions for installing the 174176 modification kit to provide Model 28 send-receive keyboard (LK6 and up) with an upper case "D" answer-back mechanism; also, kit 176272 to give answer-back operation on sequential "Figures" - "C" with addendum. 50042S 177010 Selector Magnet Driver, 177015 Modification Kit to add 177010 Selector Magnet Driver to Model 15 or Model 19 Set 50060S Instructions for installing the 178343, 178344, and 178345 modification kits on Model 28 send-receive sets (Keyboards LK6 and up) to provide an Answer-Back mechanism. 50065S Instructions for installing the 178316, 178343, 178345, and 178346 modification kits on Model 28 automatic send-receive sets (ASR) to provide an answer-back mechanism for use in dial TWX. 50010S Instructions for installing the 179416 modification kit; the 176540 tandem numbering module assembly in the LAAC232** cabinet; also, modification kit 194329** to permit using the LAAC232** cabinet without numbering module 50131S Instructions for installing the 195022 modification kit to convert FAA Model 28 ASR sets with keyboards LAK4 or 25 to conform to VSL245; kit 195023 to make FAA Model 28 ASR sets with keyboard LAK26 compatible with VSL245 sets; and kit 195036 to provide line relay and line shunt relay for auxiliary typing reperforator (LPR) for FAA. 50146S Intructions for installing the 194049 modification kit to provide an upper case "D" answer-back mechanism on Model 28 ASR sets 50152S Instructions for installing the 179953 modification kit to convert the 160334 transmitter control device to the 179472 transmitter control device 50162S Instructions for installing the 194236 modification kit to add print-suppression to the Model 35 tape printer (LTP800, 801) and Model 35 typing reperforator (LPR800, 801) 50173S Instructions for installing the 193646 modification kit to convert a Model 28 selective calling keyboard send-receive set equipped with stunt box arrangement "AFQ" (or other "AN" based arrangement) for use with Teletype Automatic Switching Package (TASP) - 60 WPM operation only 50178S Instructions for installing the 193936 (Navy nomenclature MK-764/UG) modification kit on Navy stunt boxes (LP6 and up) to permit line feed on carriage return and restrict line feed on the two functions that follow 50203S Instructions for installing the 195154 modification kit to provide three speed gear shift on Model 28 ASR sets 50204S Instructions for installing the 195415 modification kit to provide a three-speed gear shift for Model 28 KSR or RO set 50267S Instructions for installing modification kit 199520 to provide a business machine data replay mechanism to a Model 28 stunt box - 83B3 system 50333S Instructions for installing the 199886 modification kit to provide a transmitter distributor control for Model 35 ASR stations 50366S Instructions for installing the modification kits 306726 through 306730, 306986 and 306987 to convert Bell system stunt boxes for use with Model 28 83B3 typing units (LP) 50368S Installation instructions for modification kits 306721 through 306725, 306984, and 306985 to convert page printers for use in the 83B3 selective calling system 50386S Instructions for installing the 305037 and 310733 modification kits to adapt a Model 35 or Model 28 sprocket feed typing unit to take 9-1/2 inch width paper, respectively 60198S Engineering specification for the Model 28 transmitter distributor (LBXD800 and Model 35 transmitter distributor (LBXD801) 60324S Engineering specification for equipment comprising the Teletype Automatic Switching Package (TASP) 60325S Engineering specification for the automatic line switching system originating and terminating station teletypewriter equipment (Delta Airlines system) 60660S (partial) Canadian ticker